View PEB2466-HV12_1608435.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

ics for communications four channel codec filter with pcm- and m -controller interface sicofi ? 4- m c peb 2466 version 1.2 data sheet 02.97 ds 2
edition 02.97 this edition was realized using the software system framemaker a . published by siemens ag, bereich halbleiter, marketing- kommunikation, balanstra?e 73, 81541 mnchen siemens ag 1997. all rights reserved. attention please! as far as patents or other rights of third parties are concerned, liability is only assumed for components, not for applications, processes and cir- cuits implemented within compo- nents or assemblies. the information describes the type of component and shall not be consid- ered as assured characteristics. terms of delivery and rights to change design reserved. for questions on technology, deliv- ery and prices please contact the semiconductor group offices in ger- many or the siemens companies and representatives worldwide (see address list). due to technical requirements com- ponents may contain dangerous sub- stances. for information on the types in question please contact your near- est siemens office, semiconductor group. siemens ag is an approved cecc manufacturer. packing please use the recycling operators known to you. we can also help you C get in touch with your nearest sales office. by agreement we will take packing material back, if it is sorted. you must bear the costs of transport. for packing material that is returned to us unsorted or which we are not obliged to accept, we shall have to in- voice you for any costs incurred. components used in life-support devices or systems must be ex- pressly authorized for such pur- pose! critical components 1 of the semicon- ductor group of siemens ag, may only be used in life-support devices or systems 2 with the express written approval of the semiconductor group of siemens ag. 1 a critical component is a compo- nent used in a life-support device or system whose failure can rea- sonably be expected to cause the failure of that life-support device or system, or to affect its safety or ef- fectiveness of that device or sys- tem. 2 life support devices or systems are intended (a) to be implanted in the human body, or (b) to support and/or maintain and sustain hu-
peb 2466 revision history: current version: 02.97 previous versions: preliminary data sheet 05.95 errata sheet 08.95 (valid) for v1.1) errata sheet 05.96 (valid for v1.2) preliminary data sheet 03.96 last revision data sheet 06/96 page (in last revision) subjects (major changes regarding preliminary data sheet 03.96) 1 featurelist updated 2-4 chapter major applications added 5-8 errors in pin configuration fixed values of filter and coupling capacitors fixed several minor clarifications 12-15 pcm interface clarified 17 byte by byte transfer with the m c-interface added 18 types of commands and databytes clarified 19-23 several errors in programming examples fixed 25 im-filter changed to im/r1-filter 32 cram architecture described 38 error in definition of xr4-register fixed 39 error in definition of xr5-register fixed 39 definition of crash added 41 figure for setting slopes in xr6 added 45-46 chapter about programmable filters updated 46-47 chapter about qsicos added 48 clear separation of a-law and m -law 49 icn-spec updated 58 values for power dissipation and current-consumption updated 59 values for analog input and output resistance updated 60 figure for selection of optimum coupling cap. added 61-64 timing spec. figures for digital interfaces added, times updated 65 description of level metering function added 68 guidelines for boarddesign added
peb 2466 revision history: current version: 02.97 previous versions: preliminary data sheet 05.95 errata sheet 08.95 (valid for v1.1) errata sheet 05.96 (valid for v1.2) preliminary data sheet 03.96 last revision data sheet 06.96 page (in current version) subjects (major changes since last revision) 4 footnote added to the pins vdda12 and vdda34, reference added to footnote for filter-capacitors clarification, int12, int34 are active high 26 ax1 and ax2 exchanged, in figure cut offs and loops 27 footnote added regarding attenuation of hpr and hpx 39 figure setting of slopes in register xr6 updated 42 errors in description standby- and operating mode fixed (pu bit, cr1) 44 figure in chapter qsicos clarified 45 hint for tool qsucconv.exe added 46 test conditions completed 57 analog output load-spec added 58 change for clarification, r out -> r load 63 figure updated (ax1 and ax2 exchanged) 64 command description updated 65 figure proposed test circuit updated 66 layout-figure updated 5, 6, 58 coupling capacitors in transmit direction updated to 39 nf
peb 2466 table of contents page semiconductor group 5 02.97 1 general description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 1.1 features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 1.2 pin configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 1.3 pin definition and functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10 2 functional description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 2.1 sicofi ? -4- m c principles . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15 2.2 the pcm-interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18 2.3 the m -controller interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22 3 programming the sicofi ? -4- m c . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 3.1 types of command and data bytes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24 3.2 examples for sicofi ? -4 commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25 3.3 sop command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31 3.3.1 cr0 configuration register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32 3.3.2 cr1 configuration register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33 3.3.3 cr2 configuration register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34 3.3.4 cr3 configuration register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36 3.3.5 cr4 configuration register 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 3.3.6 cr5 configuration register 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .37 3.4 cop command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38 3.5 xop command . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40 3.5.1 xr0 extended register 0 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 3.5.2 xr1 extended register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .42 3.5.3 xr2 extended register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43 3.5.4 xr3 extended register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .44 3.5.5 xr4 extended register 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45 3.5.6 xr5 extended register 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .46 3.5.7 xr6 extended register 6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47 3.5.8 xr7 extended register 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48 3.5.9 setting of slopes in register xr6 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .49 3.6 the signaling interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 3.6.1 operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .50 3.6.2 programmable filters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52 3.6.3 qsicos software . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53 4 transmission characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55 4.1 frequency response . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57 4.2 group delay . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .58 4.3 out-of-band signals at analog input . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60 4.4 out-of-band signals at analog output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .61 4.5 out of band idle channel noise at analog output . . . . . . . . . . . . . . . . . . . . .62 4.6 overload compression . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63 4.7 gain tracking (receive or transmit) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .64
peb 2466 table of contents page semiconductor group 6 02.97 4.8 total distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .65 4.8.1 total distortion measured with sine wave . . . . . . . . . . . . . . . . . . . . . . . . . .65 4.8.2 total distortion measured with noise according to ccitt . . . . . . . . . . . . . .66 4.9 single frequency distortion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 4.10 transhybrid loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67 5 electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68 5.1 coupling capacitors at the analog interface . . . . . . . . . . . . . . . . . . . . . . . . .71 5.2 reset timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .71 5.3 pcm-interface timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72 5.4 m -controller interface timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74 5.5 signaling interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75 5.6 from the m c-interface to the so/sb-pins (data downstream) . . . . . . . . . . . .75 5.7 from the si/sb-pins to the m c-interface (data upstream) . . . . . . . . . . . . . . .75 6 package outlines . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76 7 appendix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 7.1 level metering function . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77 7.2 programming the sicofi ? -4- m c tone generators . . . . . . . . . . . . . . . . . . . .79 8 proposed test circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80 9 guidelines for board-design . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 9.1 board layout recommendation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 9.2 filter capacitors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .81 9.3 example of a peb 2466-board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82 iom , iom -1, iom -2, sicofi , sicofi -2, sicofi -4 and sicofi -4 m c, are registered trademarks of siemens ag.
peb 2466 general description semiconductor group 7 02.97 1 general description the four channel signal processing codec filter peb 2466 sicofi-4- m c is the logical continuation of a well established family of siemens programmable codec-filter-ics. its major difference to the peb 2465 (sicofi-4) is the pcm and m c interface, which replaces the iom-2 interface. the sicofi-4- m c is a fully integrated pcm codec and filter fabricated in low power 1 m cmos technology for applications in digital communication systems. based on an advanced digital filter concept, the peb 2466-h provides excellent transmission performance and high flexibility. the new filter concept (second generation) leads to a maximum of independence between the different filter blocks. each filter block can be seen like a one to one representative of the corresponding network element. to complete the functionality of the peb 2466 only two external capacitors per channel are needed. the internal level accuracy is based on a very accurate bandgap reference. the frequency behaviour is mainly determined by digital filters, which do not have any fluctuations. as a result of the new adc - and dac - concepts linearity is only limited by second order parasitic effects. although the device works with only one single 5 v supply there is a very good dynamic range available.
p-mqfp-64 semiconductor group 8 02.97 four channel codec filter with pcm- and m -controller interface sicofi ? 4- m c peb 2466 version 1.2 cmos type ordering code package peb 2466-h v1.2 on request p-mqfp-64 1.1 features ? single chip programmable codec and filter to handle four C central office C or pabx-channels ? specification according to relevant ccitt, eia and lssgr recommendations ? digital signal processing technique ?serial m -controller interface ? 2 programmable pcm-interfaces (up to 8 mbit/s) ? programmable interface to electronic slics and transformer solutions for signaling information ? high analog driving capability (300 w ) for direct driving of transformers ? programmable digital filters to adapt the transmission behaviour especially for C ac impedance matching C transhybrid balancing C frequency response Cgain Ca/ m -law conversion ? single 5 v power supply ? advanced low power 0.9 m m analog cmos technology ? low power consumption (< 35 mw per channel) ? high performance a/d conversion ? high performance d/a conversion ? advanced test capabilities C five digital loops C four analog loops C two programmable tone generators (dtmf possible) C built in self-test C level metering function for system tests ? standard p-mqfp-64 package ? comprehensive development platform available C software for automatic filter coefficient calculation - qsicos C hardware development board - stsi 2466
peb 2466 general description semiconductor group 9 02.97 1.2 pin configuration (top view) figure 1 p-mqfp-64
peb 2466 general description semiconductor group 10 02.97 1.3 pin definition and functions pin no. symbol input (i) output (o) function common pins for all channels 24 v ddd i + 5 v supply for the digital circuitry 1) 21 gndd i ground digital, not internally connected to gnda1,2,3,4 all digital signals are referred to this pin 52 v dda12 i + 5 v analog supply voltage for channel 1 and 2 1) 61 v dda34 i + 5 v analog supply voltage for channel 3 and 4 1) 56 v ref i/o reference voltage, has to be connected to a 220 nf cap. to ground, can also be used as virtual ground for analog inputs and outputs (high-ohmic buffer needed !!!) 57 v ddref i + 5 v analog supply voltage (100 nf cap. required) 31 fsc i frame synchronization clock, 8 khz, identifies the beginning of the frame, individual time slots are referenced to this pin, fsc must be synchronous to pclk 32 pclk i data clock 128 to 8192 khz, determines the rate at which pcm data is shifted into or out of the pcm-ports 30 drb i pcm-interface: receive pcm data from pcm-highway b, data for each channel is received in 8 bit bursts every 125 m s 29 dxb o pcm-interface: transmit pcm data to pcm-highway b, data for each channel is transmitted in 8 bit burst every 125 m s 28 tcb o pcm-interface: transmit control output b, is active if data is transmitted via dxb, active low, open drain 27 dra i pcm-interface: receive pcm data from pcm-highway a, data for each channel is received in 8 bit bursts every 125 m s 26 dxa o pcm-interface: transmit pcm data to pcm-highway a, data for each channel is transmitted in 8 bit burst every 125 m s
peb 2466 general description semiconductor group 11 02.97 25 tca o pcm-interface: transmit control output a, is active if data is transmitted via dxa, active low, open drain 23 reset i reset input - forces the device to default mode, active low 22 mclk i master clock input, 1536, 2048, 4096 or 8192 khz, synchronous to fsc, must be available if the sicofi-4- m c is used 17 cs i m -controller interface: chip select enable to read or write data, active low 18 dclk i m -controller interface: data clock, shifts data from or to device, the maximum clock rate is 8192 khz 19 din i m -controller interface: control data input pin, dclk determines the data rate 20 dout o m -controller interface: control data output pin, dclk determines the data rate, dout is high z if no data is transmitted from the sicofi-4- m c 33 chclk1 o chopper clock output, provides a programmable (2 28 ms) output signal (synchronous to mclk) 16 chclk2 o chopper clock output, provides a 256, or 512 or 16384 khz signal, is synchronous to mclk 34 int12 o interrupt output pin for channel 1 and 2, active high 15 int34 o interrupt output pin for channel 3 and 4, active high 1.3 pin definition and functions (contd) pin no. symbol input (i) output (o) function
peb 2466 general description semiconductor group 12 02.97 specific pins for channel 1 50 gnda1 i ground analog for channel 1, not internally connected to gndd or gnda2,3,4 49 v in1 i analog voice (voltage) input for channel 1, has to be connected to the slic by a 39 nf cap. 51 v out1 o analog voice (voltage) output for channel 1, has to be connected to the slic via a cap. 2) 36 si1_0 i signaling input pin 0 for channel 1 35 si1_1 i signaling input pin 1 for channel 1 41 so1_0 o signaling output pin 0 for channel 1 40 so1_1 o signaling output pin 1 for channel 1 39 sb1_0 i/o bi-directional signaling pin 0 for channel 1 38 sb1_1 i/o bi-directional signaling pin 1 for channel 1 37 sb1_2 i/o bi-directional signaling pin 2 for channel 1 specific pins for channel 2 54 gnda2 i ground analog for channel 2, not internally connected to gndd or gnda 1,3,4 55 v in2 i analog voice (voltage) input for channel 2, has to be connected to the slic by a 39 nf cap. 53 v out2 o analog voice (voltage) output for channel 2, has to be connected to the slic via a cap. 2) 47 si2_0 i signaling input pin 0 for channel 2 48 si2_1 i signaling input pin 1 for channel 2 42 so2_0 o signaling output pin 0 for channel 2 43 so2_1 o signaling output pin 1 for channel 2 44 sb2_0 i/o bi-directional signaling pin 0 for channel 2 45 sb2_1 i/o bi-directional signaling pin 1 for channel 2 46 sb2_2 i/o bi-directional signaling pin 2 for channel 2 1.3 pin definition and functions (contd) pin no. symbol input (i) output (o) function
peb 2466 general description semiconductor group 13 02.97 specific pins for channel 3 59 gnda3 i ground analog for channel 3, not internally connected to gndd or gnda1,2,4 58 v in3 i analog voice (voltage) input for channel 3, has to be connected to the slic by a 39 nf cap. 60 v out3 o analog voice (voltage) output for channel 3, has to be connected to the slic via a cap. 2) 2 si3_0 i signaling input pin 0 for channel 3 1 si3_1 i signaling input pin 1 for channel 3 7 so3_0 o signaling output pin 0 for channel 3 6 so3_1 o signaling output pin 1 for channel 3 5 sb3_0 i/o bi-directional signaling pin 0 for channel 3 4 sb3_1 i/o bi-directional signaling pin 1 for channel 3 3 sb3_2 i/o bi-directional signaling pin 2 for channel 3 1.3 pin definition and functions (contd) pin no. symbol input (i) output (o) function
peb 2466 general description semiconductor group 14 02.97 1) a 100 nf cap. should be used for blocking these pins, see also on page 82 2) the value for the capacitor needed, depends on the input impedance of the slic-circuitry. for choosing the appropriate values see figure on page 71. specific pins for channel 4 63 gnda4 i ground analog for channel 4, not internally connected to gndd or gnda1,2,3 64 v in4 i analog voice (voltage) input for channel 4, has to be connected to the slic by a 39 nf cap. 62 v out4 o analog voice (voltage) output for channel 4, has to be connected to the slic via a cap. 2) 13 si4_0 i signaling input pin 0 for channel 4 14 si4_1 i signaling input pin 1 for channel 4 8 so4_0 o signaling output pin 0 for channel 4 9 so4_1 o signaling output pin 1 for channel 4 10 sb4_0 i/o bi-directional signaling pin 0 for channel 4 11 sb4_1 i/o bi-directional signaling pin 1 for channel 4 12 sb4_2 i/o bi-directional signaling pin 2 for channel 4 1.3 pin definition and functions (contd) pin no. symbol input (i) output (o) function
peb 2466 functional description semiconductor group 15 02.97 2 functional description 2.1 sicofi ? -4- m c principles the change from 2 m m to 1 m m cmos process requires new concepts in the realization of the analog functions. high performance (in the terms of gain, speed, stability ) 1 m m cmos devices cannot withstand more than 5.5 v of supply-voltage. on that account the negative supply voltage vss of the previous sicofis is omitted. this is a benefit for the user but it makes a very high demand on the analog circuitry. adc and dac are changed to sigma-delta-concepts to fulfill the stringent requirements on the dynamic parameters. using 1 m m cmos does not only lead to problems - it is the only acceptable solution in terms of area and power consumption for the integration of more than two sicofi channels on a single chip. it is rather pointless to implement 4 codec-filter-channels on one chip with pure analog circuitry. the use of a dsp-concept (the sicofi and the sicofi-2-approach) for this function is a must for an adequate four channel architecture. figure 2 sicofi ? -4 m c signal flow graph (for any channel)
peb 2466 functional description semiconductor group 16 02.97 transmit path the analog input signal has to be dc-free connected by an external capacitor because there is an internal virtual reference ground potential. after passing a simple antialiasing prefilter (prefi) the voice signal is converted to a 1-bit digital data stream in the sigma-delta-converter. the first downsampling steps are done in fast running digital hardware filters. the following steps are implemented in the micro-code which has to be executed by the central digital signal processor. this dsp-machine is able to handle the workload for all four channels. at the end the fully processed signal (flexibly programmed in many parameters) is transferred to the pcm- interface in a pcm-compressed signal representation. receive path the digital input signal is received via the pcm interface. expansion, pcm-law-pass-filtering, gain correction and frequency response correction are the next steps which are done by the dsp-machine. the upsampling interpolation steps are again processed by fast hardware structures to reduce the dsp-workload. the upsampled 1-bit data stream is then converted to an analog equivalent which is smoothed by a post-filter (pofi). as the signal v out is also referenced to an internal virtual ground potential, an external capacitor is required for dc-decoupling. loops there are two loops implemented. the first is to generate the ac-input impedance (im) and the second is to perform a proper hybrid balancing (th). a simple extra path im2 (from the transmit to the receive path) supports the impedance matching function. test features there are four analog and five digital test loops implemented in the sicofi-4. for special tests it is possible to cut off the receive and the transmit path at two different points.
peb 2466 functional description semiconductor group 17 02.97 figure 3 sicofi ? -4- m c block diagram the sicofi-4- m c bridges the gap between analog and digital voice signal transmission in modern telecommunication systems. high performance oversampling analog-to-digital converters (adc) and digital-to-analog converters (dac) provide the conversion accuracy required. analog antialiasing prefilters (prefi) and smoothing postfilters (pofi) are included. the connection between the adc and the dac (with high sampling rate) and the dsp, is done by specific hardware filters, for filtering like interpolation and decimation. the dedicated digital signal processor (dsp) handles all the algorithms necessary e.g. for pcm bandpass filtering, sample rate conversion and pcm companding. the pcm-interface handles digital voice transmission, a serial m c-interface handles sicofi-4- m c feature control and transparent access to the sicofi-4- m c command and indication pins. to program the filters, precalculated sets of coefficients are downloaded from the system to the on-chip coefficient-ram (cram). itb07256 hw-filter analog out analog in analog in analog out hw-filter dsp hw-filter hw-filter analog out indication analog in analog out command analog in command indication signaling indication command command indication signaling signaling signaling d a d a control data c interface pcm interface voice data m d a a d d a a d d a a d
peb 2466 functional description semiconductor group 18 02.97 2.2 the pcm-interface two serial pcm-interfaces are used for the transfer of a- or m -law compressed voice data. the pcm-interface consist of 8 pins: the frame sync fsc pulse identifies the beginning of a receive and transmit frame for all of the four channels. the pclk clock is the signal to synchronize the data transfer on both lines dxa (dxb) and dra (drb). bytes in all channels are serialized to 8 bit width and msb first. as a default setting, the rising edge indicates the start of the bit, while the falling edge is used to latch the contents of the received data on dra (drb). if the double clock rate is chosen (twice the transmission rate) the first rising edge indicates the start of a bit, while the second falling edge is used for latching the contents of the data line dra (drb) by default. the data rate of the interface can vary from 2 128 kbit/s to 2 8192 kbit/s (2 highways) a frame may consist of up to 128 time slots of 8 bits each. in the time slot configuration registers cr5 and cr6 the user can select an individual time slot, and an individual pcm-highway, for any of the four voice channels. receive and transmit time slots can also be programmed individually. an extra delay of up to 7 clocks, valid for all channels, as well as the sampling slope may be programmed (see xr6). when the sicofi-4- m c is transmitting data on dxa (dxb), pin tca (tcb) is activated to control an extra external driving device. pclk: pcm-clock, 128 khz to 8192 khz fsc: frame synchronization clock, 8 khz dra: receive data input for pcm-highway a drb: receive data input for pcm-highway b dxa: transmit data output for pcm-highway a dxb: transmit data output for pcm-highway b tca: transmit control output for pcm-highway a, active low during transmission tcb: transmit control output for pcm-highway b, active low during transmission
peb 2466 functional description semiconductor group 19 02.97 the following table shows possible examples for the pcm-interface, other frequencies like 768 khz or 1536 khz are also possible. table 1 frequency [khz] single/double [1/2] time slots [per highway] datarate [kbit/s per highway] 128 1 2 128 256 2 2 128 256 1 4 256 512 2 4 256 512 1 8 512 1024 2 8 512 1024 1 16 1024 2048 2 16 1024 2048 1 32 2048 4096 2 32 2048 4096 1 64 4096 8192 2 64 4096 8192 1 128 8192 formula f 1 f/64 f formula f 2 f/128 f/2
peb 2466 functional description semiconductor group 20 02.97 figure 4 example for single clock rate, 128 kbit/s figure 5 example for double clock rate, 128 kbit/s
peb 2466 functional description semiconductor group 21 02.97 figure 6 example for 2048 kbit/s, single clock operation, only highway a used figure 7 detail a for special purposes the dra/b and dxa/b pins may be strapped together, and form bi-directional data-pin (like sip with the sld-bus). tca detail a itd07259 time-slot 31 fsc dxa dra pclk 23 high 'z' m 125 s high 'z' time-slot 01 itd07260 dra pclk fsc dxa tca high 'z' high 'z' voice data voice data clock 0 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 bit
peb 2466 functional description semiconductor group 22 02.97 2.3 the m -controller interface the internal configuration registers, the signaling interface, and the coefficient-ram (cram) of the sicofi-4- m c are programmable via a serial m -controller interface. the m -controller interface consists of four lines: cs, dclk, din and dout: cs is used to start a serial access to the sicofi-4- m c registers and coefficient-ram. following a falling edge of cs, the first eight bits received on din specify the command. subsequent data bytes (number depends on command) are stored in the selected configuration registers or the selected part of the coefficient-ram. figure 8 example for a write access, with two data bytes transferred if the first eight bits received via din specify a read-command, the sicofi-4 will start a response via dout with its specific address byte (81 h ). after transmitting this identification, the specified n data bytes (contents of configuration registers, or contents of the cram) will follow on dout. itd07261 76543210 0 1 2 3 4 5 6 70 1 2 3 4 5 6 7 din dout dclk cs control data byte 1 data byte 2 high 'z'
peb 2466 functional description semiconductor group 23 02.97 figure 9 example for a read access, with one data byte transferred via dout the data transfer is synchronized by the dclk input. the contents of din is latched at the rising edge of dclk, while dout changes with the falling edge of dclk. during execution of commands that are followed by output data (read commands), the device will not accept any new command via din. the data transfer sequence can be broken by setting cs to high. to reduce the number of connections to the m p din and dout may be strapped together, and form a bi-directional data-pin. for special applications a byte by byte transfer is needed. this can be done by prolonging the high time of dclk for a user defined waiting time after transferring any byte. figure 10 example for a write/read access, with a byte by byte transfer, and din and dout strapped together the identification byte is 81 h for the peb 2466. itd07262 76543210 din dout dclk cs control data byte 1 high 'z' 7654321076543210 high 'z' identification itd09570 76543210 0 1 2 3 4 5 6 70 1 2 3 4 5 6 7 data dclk cs control-byte identification high 'z' data byte 1
peb 2466 programming the sicofi ? -4- m c semiconductor group 24 02.97 3 programming the sicofi ? -4- m c with the appropriate commands, the sicofi-4- m c can be programmed and verified very flexibly via the m -controller interface. with the first byte received via din, one of 3 different types of commands (sop, xop and cop) is selected. each of those can be used as a write or read command. due to the extended sicofi-4- m c feature control facilities, sop, cop and xop commands contain additional information (e.g. number of subsequent bytes) for programming (write) and verifying (read) the sicofi-4- m c status. a write command is followed by up to 8 bytes of data. the sicofi-4- m c responds to a read command with its specific identification and the requested information, that is up to 8 bytes of data. 3.1 types of command and data bytes the 8-bit bytes have to be interpreted as either commands or status information stored in configuration registers or the coefficient-ram. there are three different types of sicofi -4- m c commands which are selected by bit 3 and 4 as shown below. sop status operation: sicofi-4- m c status setting/monitoring xop extended operation: c/i 1) channel configuration/evaluation cop coefficient operation: filter coefficient setting/monitoring note: 1) command/indication (signaling) channel. bit 7 0 ad2 ad1 1 0 bit 7 0 011 bit 7 0 ad2 ad1 0
peb 2466 programming the sicofi ? -4- m c semiconductor group 25 02.97 storage of programming information 3.2 examples for sicofi ? -4 commands sop - write commands 6 configuration registers per channel: cr0, cr1, cr2, cr3, cr4 and cr5 accessed by sop commands 8 common configuration registers: xr0 .. xr7 accessed by xop commands, valid for all 4 channels 1 coefficient-ram per channel: cram accessed by cop commands din 76543210 bit 76543210 dout sop-write 1 byte 010000 idle cr0 data idle din 76543210 bit 76543210 dout sop-write 2 bytes 010001 idle cr1 data idle cr0 data idle din 76543210 bit 76543210 dout sop-write 3 bytes 010010 idle cr2 data idle cr1 data idle cr0 data idle din 76543210 bit 76543210 dout sop-write 4 bytes 010011 idle cr3 data idle cr2 data idle cr1 data idle cr0 data idle
peb 2466 programming the sicofi ? -4- m c semiconductor group 26 02.97 xop - write commands cop - write commands din 76543210 bit 76543210 dout xop-write 2 bytes 011001 idle xr1 data idle xr0 data idle din 76543210 bit 76543210 dout xop-write 3 bytes 011010 idle xr2 data idle xr1 data idle xr0 data idle din 76543210 bit 76543210 dout cop-write 4 bytes 0 0 idle coeff. 3 data idle coeff. 2 data idle coeff. 1 data idle coeff. 0 data idle din 76543210 bit 76543210 dout cop-write 8 bytes 0 0 idle coeff. 7 data idle coeff. 6 data idle coeff. 5 data idle coeff. 4 data idle coeff. 3 data idle coeff. 2 data idle coeff. 1 data idle coeff. 0 data idle
peb 2466 programming the sicofi ? -4- m c semiconductor group 27 02.97 sop - read commands din 76543210 bit 76543210 dout sop-read 1 byte 1 1 0 0 0 0 idle idle 10000001identification idle data cr0 din 76543210 bit 76543210 dout sop-read 2 bytes 1 1 0 0 0 1 idle idle 10000001identification idle data cr1 idle data cr0 din 76543210 bit 76543210 dout sop-read 3 bytes 1 1 0 0 1 0 idle idle 10000001identification idle data cr2 idle data cr1 idle data cr0 din 76543210 bit 76543210 dout sop-read 4 bytes 1 1 0 0 1 1 idle idle 10000001identification idle data cr3 idle data cr2 idle data cr1 idle data cr0
peb 2466 programming the sicofi ? -4- m c semiconductor group 28 02.97 xop-read commands din 76543210 bit 76543210 dout xop-read 1 byte 1 11000 idle idle 10000001identification idle data xr0 din 76543210 bit 76543210 dout xop-read 2 bytes 1 1 1 0 0 1 idle idle 10000001i dentification idle data xr1 idle data xr0 din 76543210 bit 76543210 dout xop-read 3 bytes 1 1 1 0 1 0 idle idle 10000001i dentification idle data xr2 idle data xr1 idle data xr0
peb 2466 programming the sicofi ? -4- m c semiconductor group 29 02.97 cop-read commands din 76543210 bit 76543210 dout cop-read 4 bytes 1 0 1 idle idle 10000001identification idle data coeff. 3 idle data coeff. 2 idle data coeff. 1 idle data coeff. 0 din 76543210 bit 76543210 dout cop-read 8 bytes 1 0 0 idle idle 10000001identification idle data coeff. 8 idle data coeff. 7 idle data coeff. 6 idle data coeff. 5 idle data coeff. 4 idle data coeff. 3 idle data coeff. 2 idle data coeff. 1
peb 2466 programming the sicofi ? -4- m c semiconductor group 30 02.97 example of a mixed command din 76543210bit76543210 dout sop-write 4 bytes 010011 idle cr3 data idle cr2 data idle cr1 data idle cr0 data idle xop-write 2 bytes 011001 idle xr1 data idle xr0 data idle cop-write 4 bytes 0 0 1 idle coeff. 3 data idle coeff. 2 data idle coeff. 1 data idle coeff. 0 data idle sop-read 3 bytes 110010 idle idle 1 0 0 0 0 0 0 1 identification idle data cr2 idle data cr1 idle data cr0 cop-read 4 bytes 1 0 1 idle idle 1 0 0 0 0 0 0 1 identification idle data coeff. 3 idle data coeff. 2 idle data coeff. 1 idle data coeff. 0 xop-read 1 byte 111000 idle idle 1 0 0 0 0 0 0 1 identification idle data xr0
peb 2466 programming the sicofi ? -4- m c semiconductor group 31 02.97 3.3 sop command to modify or evaluate the sicofi-4- m c status, the contents of up to 6 configuration registers cr0 .. cr7 may be transferred to or from the sicofi-4- m c. this is started by a sop-command (status operation command). note: if only one configuration register requires modification, for example cr5, this can be accomplished by setting lsel = 101 and releasing pin cs after cr5 is written. bit 7 0 ad2 ad1 rw 1 0 lsel2 lsel1 lsel0 ad address information ad = 00 sicofi-4- m c - channel 1 is addressed with this command ad = 01 sicofi-4- m c - channel 2 is addressed with this command ad = 10 sicofi-4- m c - channel 3 is addressed with this command ad = 11 sicofi-4- m c - channel 4 is addressed with this command rw read/write information: enables reading from the sicofi-4- m c or writing information to the sicofi-4- m c rw = 0 write to sicofi-4 m c rw = 1 read from sicofi-4 m c lsel length select information (see also programming procedure) this field identifies the number of subsequent data bytes lsel = 000 1 byte of data is following (cr0) lsel = 001 2 bytes of data are following (cr1, cr2) lsel = 010 3 bytes of data are following (cr2, cr1, cr0) lsel = 011 4 bytes of data are following (cr3, cr2, cr1, cr0) lsel = 100 5 bytes of data are following (cr4, cr3, cr2, cr1, cr0) lsel = 101 6 bytes of data are following (cr5, cr4, cr3, cr2, cr1, cr0) all other codes are reserved for future use !
peb 2466 programming the sicofi ? -4- m c semiconductor group 32 02.97 3.3.1 cr0 configuration register 0 configuration register cr0 defines the basic sicofi-4- m c settings, which are: enabling/ disabling the programmable digital filters. bit 7 0 th im/r1 frx frr ax ar th-sel th enable th- (trans hybrid balancing) filter th = 0: th-filter disabled th = 1: th-filter enabled im/r1 enable im-(impedance matching) filter and r1-filter im/r1 = 0: im-filter and r1-filter disabled im/r1 = 1: im-filter and r1-filter enabled frx enable frx (frequency response transmit)-filter frx = 0: frx-filter disabled frx = 1: frx-filter enabled frr enable frr (frequency response receive)-filter frr = 0: frr-filter disabled frr = 1: frr-filter enabled ax enable ax-(amplification/attenuation transmit) filter ax = 0: ax-filter disabled ax = 1: ax-filter enabled ar enable ar-(amplification/attenuation receive) filter ar = 0: ax-filter disabled ar = 1: ax-filter enabled th-sel 2 bit field to select one of four programmed th-filter coefficient sets th-sel = 0 0: th-filter coefficient set 1 is selected th-sel = 0 1: th-filter coefficient set 2 is selected th-sel = 1 0: th-filter coefficient set 3 is selected th-sel = 1 1: th-filter coefficient set 4 is selected
peb 2466 programming the sicofi ? -4- m c semiconductor group 33 02.97 3.3.2 cr1 configuration register 1 configuration register cr1 selects tone generator modes and other operation modes. 1) tone generator 2 is not available if level metering function is enabled! bit 7 0 etg2 etg1 ptg2 ptg1 law 0 0 pu etg2 enable programmable tone generator 2 1) etg2 = 0: programmable tone generator 2 is disabled etg2 = 1: programmable tone generator 2 is enabled etg1 enable programmable tone generator 1 etg1 = 0: programmable tone generator 1 is disabled etg1 = 1: programmable tone generator 1 is enabled ptg2 user programmed frequency or fixed frequency is selected ptg2 = 0: fixed frequency for tone generator 2 is selected (1 khz) ptg2 = 1: programmed frequency for tone generator 2 is selected ptg1 user programmed frequency or fixed frequency is selected ptg1 = 0: fixed frequency for tone generator 1 is selected (1 khz) ptg1 = 1: programmed frequency for tone generator 1 is selected law pcm - law selection law = 0: a-law is selected law = 1: m -law ( m 255 pcm) is selected pu power up, sets the addressed channel to power up / down pu = 0: the addressed channel is set to power down (standby) pu = 1: the addressed channel is set to power up (operating)
peb 2466 programming the sicofi ? -4- m c semiconductor group 34 02.97 3.3.3 cr2 configuration register 2 1) explanation of the level metering function: a signal fed to a/ m -law compression via ax- and hpx-filters (from a digital loop, or externally via vin), is rectified, and the power is measured. if the power exceeds a certain value, loaded to xr7, bit lmr is set to 1. the power of the incoming signal can be adjusted by ax-filters. bit 7 0 cot/r 0 idr lm lmr v+t cot/r selection of cut off transmit/receive paths 0 0 0: normal operation 0 0 1: cot16 cut off transmit path at 16 khz (input of th-filter) 0 1 0: cot8 cut off transmit path at 8 khz (input of compression, output is zero for m -law, 1 lsb for a-law) 1 0 1: cor4m cut off receive path at 4 mhz (pofi-output) 1 1 0: cor64 cut off receive path at 64 khz (im-filter input) idr initialize data ram idr = 0: normal operation is selected idr = 1: contents of data ram is set to 0 (used for production test purposes) lm level metering function 1) lm = 0: level metering function is disabled lm = 1: level metering function is enabled lmr result of level metering function (this bit can not be written) lmr = 0: level detected was lower than the reference lmr = 1: level detected was higher than the reference v+t add voice signal and tone generator signal v+t = 0: voice or tone generator is fed to the dac v+t = 1: voice and tone generator signals are added, and fed to the digital to analog converter
peb 2466 programming the sicofi ? -4- m c semiconductor group 35 02.97 figure 11 cut offs and loops its09608 agr vout agx vin + us3 im2* ds1 us1 ds3 im 1* ax2* ar2* th* hpr tg1, 2 exp hpx cmp pcmin pcmout transmit path receive path frx* frr* a ds2 us2 r1* ar1* ax1* alb-pfi dlb-4m alb-4m dlb-128k dlb-64k alb-8k dlb-pcm alb-pcm cor-pfi cot-16k cot-pcm 4 mhz 256 khz 128 khz 64 khz 16 khz 8 khz dlb-ana cor-64k d a d
peb 2466 programming the sicofi ? -4- m c semiconductor group 36 02.97 3.3.4 cr3 configuration register 3 1) in this case the transmit-path signal is attenuated 0.06 db 2) in this case the receive-path signal is attenuated 0.12 db bit 7 0 test-loops agx agr d-hpx d-hpr test-loops 4 bit field for selection of analog and digital loop backs 0 0 0 0: no loop back is selected (normal operation) 0 0 0 1: alb-pfi analog loop back via prefi-pofi is selected 0 0 1 1: alb-4m analog loop back via 4 mhz is selected 0 1 0 0: alb-pcm analog loop back via 8 khz (pcm) is selected (attention: special settings necessary) 0 1 0 1: alb-8k analog loop back via 8 khz (linear) is selected 1 0 0 0: dlb-ana digital loop back via analog port is selected 1 0 0 1: dlb-4m digital loop back via 4 mhz is selected 1 1 0 0: dlb-128k digital loop back via 128 khz is selected 1 1 0 1: dlb-64k digital loop back via 64 khz is selected 1 1 1 1: dlb-pcm digital loop back via pcm-registers is selected agx analog gain in transmit direction agx = 0: analog gain is disabled agx = 1: analog gain is enabled (6.02 db amplification) agr analog gain in receive direction agr = 0: analog gain is disabled agr = 1: analog gain is enabled (6.02 db attenuation) d-hpx disable highpass in transmit direction d-hpx = 0: transmit high pass is enabled d-hpx = 1: transmit high pass is disabled 1) d-hpr disable highpass in receive direction d-hpr = 0: receive high pass is enabled d-hpr = 1: receive high pass is disabled 2)
peb 2466 programming the sicofi ? -4- m c semiconductor group 37 02.97 3.3.5 cr4 configuration register 4 configuration register cr4, sets the receiving time slot and the receiving pcm-highway. 3.3.6 cr5 configuration register 5 configuration register cr5, sets the transmit time slot and the transmit pcm-highway. bit 7 0 r-way rs6 rs5 rs4 rs3 rs2 rs1 rs0 r-way selects the pcm-highway for the receiving of pcm-data r-way = 0: pcm-highway a is selected r-way = 1: pcm-highway b is selected rs[6:0] selects the time slot (0 to 127) used for receiving the pcm-data the time slot-number is binary coded. 0 0 0 0 0 0 0: time slot 0 is selected 0 0 0 0 0 0 1: time slot 1 is selected .... 1 1 1 1 1 1 0: time slot 126 is selected 1 1 1 1 1 1 1: time slot 127 is selected bit 7 0 x-way xs6 xs5 xs4 xs3 xs2 xs1 xs0 x-way selects the pcm-highway for transmitting pcm-data x-way = 0: pcm-highway a is selected x-way = 1: pcm-highway b is selected xs[6:0] selects the time slot (0 to 127) used for transmitting the pcm-data the time slot-number is binary coded. 0 0 0 0 0 0 0: time slot 0 is selected 0 0 0 0 0 0 1: time slot 1 is selected .... 1 1 1 1 1 1 0: time slot 126 is selected 1 1 1 1 1 1 1: time slot 127 is selected
peb 2466 programming the sicofi ? -4- m c semiconductor group 38 02.97 3.4 cop command with a cop command coefficients for the programmable filters can be written to the sicofi-4- m c coefficient-ram or read from the coefficient-ram via the m -controller interface for verification bit 7 0 ad2 ad1 rw 0 code3 code2 code1 code0 ad address ad = 0 0 sicofi-4- m c- channel 1 is addressed ad = 0 1 sicofi-4- m c- channel 2 is addressed ad = 1 0 sicofi-4- m c- channel 3 is addressed ad = 1 1 sicofi-4- m c- channel 4 is addressed rw read/write rw = 0 subsequent data is written to the sicofi-4- m c rw = 1 read data from sicofi-4- m c code includes number of following bytes and filter-address 0 0 0 0 th-filter coefficients (part 1) (followed by 8 bytes of data) 0 0 0 1 th-filter coefficients (part 2) (followed by 8 bytes of data) 0 0 1 0 th-filter coefficients (part 3) (followed by 8 bytes of data) 0 1 0 0 im/r1-filter coefficients (part 1) (followed by 8 bytes of data) 0 1 0 1 im/r1-filter coefficients (part 2) (followed by 8 bytes of data) 0 1 1 0 frx-filter coefficients (followed by 8 bytes of data) 0 1 1 1 frr-filter coefficients (followed by 8 bytes of data) 1 0 0 0 ax-filter coefficients (followed by 4 bytes of data) 1 0 0 1 ar-filter coefficients (followed by 4 bytes of data) 1 1 0 0 tg 1- coefficients (followed by 4 bytes of data) 1 1 0 1 tg 2- coefficients (followed by 4 bytes of data)
peb 2466 programming the sicofi ? -4- m c semiconductor group 39 02.97 how to program the filter coefficients figure 12 th-filter: four sets of th-filter coefficients can be loaded to the sicofi-4- m c. each of the four sets can be selected for any of the four sicofi-4- m c channels, by setting the value of th-sel in configuration register cr2. coefficient set 1 is loaded to the sicofi-4- m c via channel 1, set 2 is loaded via channel 2 and so on. ax, ar, im/r1, frx, frr-filter, tone-generators: an individual coefficient set is available for each of the four channels.
peb 2466 programming the sicofi ? -4- m c semiconductor group 40 02.97 3.5 xop command with the xop command the sicofi-4- m c digital command/indication interface to a slic is configured and evaluated. also other common functions are assigned with this command. note: all other codes are reserved for future use! if only one configuration register requires modification, for example xr5, this can be accomplished by setting lsel =101 and releasing pin cs after xr5 is written. bit 7 0 rst 0 rw 1 1 lsel2 lsel1 lsel0 rst software reset (same as reset-pin, valid for all 4 channels) rst = 1: reset rst = 0: no operation rw read / write information: enables reading from the sicofi-4- m c or writing information to the sicofi-4- m c rw = 0: write to sicofi-4- m c rw = 1: read from sicofi-4- m c lsel length select information, for setting the number of subsequent data bytes lsel = 000: 1 byte of data is following (xr0) lsel = 001: 2 bytes of data are following (xr1, xr0) : lsel = 111: 8 bytes of data are following (xr7, xr6, xr5, xr4, xr3, xr2, xr1, xr0)
peb 2466 programming the sicofi ? -4- m c semiconductor group 41 02.97 3.5.1 xr0 extended register 0 the signaling connection between sicofi-4- m c and a slic is performed by master device the sicofi-4- m c signaling input and output pins and configuration register xr0... xr4. data received from the upstream master device are transferred to signaling output pins (so, sb). data at the signaling input pins are transferred to the upstream controller. in connection with xop-read commands in connection with xop-write commands bit 7 0 si4_1 si4_0 si3_1 si3_0 si2_1 si2_0 si1_1 si1_0 si4_1 status of pin si4_1 is transferred to the upstream master device si4_0 status of pin si4_0 is transferred to the upstream master device si3_1 status of pin si3_1 is transferred to the upstream master device si3_0 status of pin si3_0 is transferred to the upstream master device si2_1 status of pin si2_1 is transferred to the upstream master device si2_0 status of pin si2_0 is transferred to the upstream master device si1_1 status of pin si1_1 is transferred to the upstream master device si1_0 status of pin si1_0 is transferred to the upstream master device bit 7 0 so4_1 so4_0 so3_1 so3_0 so2_1 so2_0 so1_1 so1_0 so4_1 pin so4_1 is set to the assigned value so4_0 pin so4_0 is set to the assigned value so3_1 pin so3_1 is set to the assigned value so3_0 pin so3_0 is set to the assigned value so2_1 pin so2_1 is set to the assigned value so2_0 pin so2_0 is set to the assigned value so1_1 pin so1_1 is set to the assigned value so1_0 pin so1_0 is set to the assigned value
peb 2466 programming the sicofi ? -4- m c semiconductor group 42 02.97 3.5.2 xr1 extended register 1 this register transfers information to or from the programmable signaling pins. in connection with a xop-read command in connection with a xop-write command note: after a reset of the device, all programmable pins are input pins! bit 7 0 sb4_1 sb4_0 sb3_1 sb3_0 sb2_1 sb2_0 sb1_1 sb1_0 sb4_1 if input: status of pin sb4_1 is transferred upstream sb4_0 if input: status of pin sb4_0 is transferred upstream sb3_1 if input: status of pin sb3_1 is transferred upstream sb3_0 if input: status of pin sb3_0 is transferred upstream sb2_1 if input: status of pin sb2_1 is transferred upstream sb2_0 if input: status of pin sb2_0 is transferred upstream sb1_1 if input: status of pin sb1_1 is transferred upstream sb1_0 if input: status of pin sb1_0 is transferred upstream sb4_1 if output: pin sb4_1 is set to the assigned value sb4_0 if output: pin sb4_0 is set to the assigned value sb3_1 if output: pin sb3_1 is set to the assigned value sb3_0 if output: pin sb3_0 is set to the assigned value sb2_1 if output: pin sb2_1 is set to the assigned value sb2_0 if output: pin sb2_0 is set to the assigned value sb1_1 if output: pin sb1_1 is set to the assigned value sb1_0 if output: pin sb1_0 is set to the assigned value
peb 2466 programming the sicofi ? -4- m c semiconductor group 43 02.97 3.5.3 xr2 extended register 2 this register controls the direction of the programmable signaling pins. note: after a reset of the device, all programmable pins are input pins! bit 7 0 psb4_1 psb4_0 psb3_1 psb3_0 psb2_1 psb2_0 psb1_1 psb1_0 psb4_1 programmable bi-directional signaling pin sb4_1 is programmed psb4_1 = 0: pin sb4_1 is indication input psb4_1 = 1: pin sb4_1 is command output psb4_0 programmable bi-directional signaling pin sb4_0 is programmed psb4_0 = 0: pin sb4_0 is indication input psb4_0 = 1: pin sb4_0 is command output psb3_1 programmable bi-directional signaling pin sb3_1 is programmed psb3_1 = 0: pin sb3_1 is indication input psb3_1 = 1: pin sb3_1 is command output psb3_0 programmable bi-directional signaling pin sb3_0 is programmed psb3_0 = 0: pin sb3_0 is indication input psb3_0 = 1: pin sb3_0 is command output psb2_1 programmable bi-directional signaling pin sb2_1 is programmed psb2_1 = 0: pin sb2_1 is indication input psb2_1 = 1: pin sb2_1 is command output psb2_0 programmable bi-directional signaling pin sb2_0 is programmed psb2_0 = 0: pin sb2_0 is indication input psb2_0 = 1: pin sb2_0 is command output psb1_1 programmable bi-directional signaling pin sb1_1 is programmed psb1_1 = 0: pin sb1_1 is indication input psb1_1 = 1: pin sb1_1 is command output psb1_0 programmable bi-directional signaling pin sb1_0 is programmed psb1_0 = 0: pin sb1_0 is indication input psb1_0 = 1: pin sb1_0 is command output
peb 2466 programming the sicofi ? -4- m c semiconductor group 44 02.97 3.5.4 xr3 extended register 3 this register transfers information to or from the programmable signaling pins and configures these pins. in connection with a xop-read command in connection with a xop-write command note: after a reset of the device, all programmable pins are input pins! bit 7 0 sb4_2 sb3_2 sb2_2 sb1_2 psb4_2 psb3_2 psb2_2 psb1_2 sb4_2 if input: status of pin sb4_2 is transferred upstream sb3_2 if input: status of pin sb3_2 is transferred upstream sb2_2 if input: status of pin sb2_2 is transferred upstream sb1_2 if input: status of pin sb1_2 is transferred upstream sb4_2 if output: pin sb4_2 is set to the assigned value sb3_2 if output: pin sb3_2 is set to the assigned value sb2_2 if output: pin sb2_2 is set to the assigned value sb1_2 if output: pin sb1_2 is set to the assigned value psb4_2 programmable bi-directional signaling pin sb4_2 is programmed psb4_2 = 0: pin sb4_2 is indication input psb4_2 = 1: pin sb4_2 is command output psb3_2 programmable bi-directional signaling pin sb3_2 is programmed psb3_2 = 0: pin sb3_2 is indication input psb3_2 = 1: pin sb3_2 is command output psb2_2 programmable bi-directional signaling pin sb2_2 is programmed psb2_2 = 0: pin sb2_2 is indication input psb2_2 = 1: pin sb2_2 is command output psb1_2 programmable bi-directional signaling pin sb1_2 is programmed psb1_2 = 0: pin sb1_2 is indication input psb1_2 = 1: pin sb1_2 is command output
peb 2466 programming the sicofi ? -4- m c semiconductor group 45 02.97 3.5.5 xr4 extended register 4 register xr4 provides two optional functions: debouncing of signaling input changes, and the configuration of the programmable output pin chclk1. signaling debounce interval n to restrict the rate of changes on signaling input pins transferred, deglitching of the status information from the slic may be applied. new status information will be read into registers xr0, xr1, xr2 and xr3, and an interrupt on pin int12 (int34) will be generated, after it has been stable for n milliseconds. n is programmable in the range of 2 to 30 ms in steps of 2 ms, with n = 0 the debouncing is disabled. configuration of chclk1 bit 7 0 nt field n debounce interval time 0 0 0 0 debounce and interrupt generation is disabled 0 0 0 1 debounce period 2 ms 0 0 1 0 debounce period 4 ms . .... . .... 1 1 1 0 debounce period 28 ms 1 1 1 1 debounce period 30 ms field t frequency applied to pin chclk1 0 0 0 0 chclk1 is set to 1 permanently 0 001t is 2ms 0 010t is 4ms . .... . .... 1 110t is 28 ms 1 1 1 1 chclk1 is set to 0 permanently
peb 2466 programming the sicofi ? -4- m c semiconductor group 46 02.97 3.5.6 xr5 extended register 5 this register contains additional configuration items valid for all 4 channels 1) a crash occurs, if 2 or more channels are programed to transmit (talk) in the same time slot on the same highway. in this case the crash-bit will be set, and transmission will be disabled for all affected channels. bit 7 0 mclk-sel crsh_a crsh_b chclk2 version mclk-sel selects master clock frequency, that has to be applied to pin mclk the mclk signal has to synchronous to the 8 khz fsc-signal. 0 0: 1536 khz selected 0 1: 2048 khz selected 1 0: 4096 khz selected 1 1: 8192 khz selected crsh_a crash 1) on pcm-highway a (line dxa) 0: no crash detected 1: crash detected (bad programming in cr5-registers) crsh_b crash on pcm-highway b (line dxb) 0: no crash detected 1: crash detected (bad programming in cr5-registers) chclk2 enables chopper clock output to pin chclk2 0 0: pin chclk2 is set to 1 0 1: a 512 khz signal is fed to pin chclk2 1 0: a 256 khz signal is fed to pin chclk2 1 1: a 16384 khz signal (internal masterclock) is fed to pin chclk2 (at least one of the four channels has to be set to power up) version this two bit field identifies the actual chip version, is 00 for version 1.1, and 01 for version 1.2
peb 2466 programming the sicofi ? -4- m c semiconductor group 47 02.97 3.5.7 xr6 extended register 6 this register configures the operation of the pcm-interface bit 7 0 c-mode x-s r-s drv_0 shift pcm-offset c-mode defines the clk-mode for the pcm-interface c-mode = 0: single clocking is used c-mode = 1: double clocking is used x-s transmit slope x-s = 0: transmission starts with rising edge x-s = 1: transmission starts with falling edge r-s receive slope r-s= 0: data is sampled with falling edge of pclk r-s= 1: data is sampled with rising edge of pclk drv_0 driving mode for bit 0 (only available with single clocking mode) drv_0 = 0: bit 0 is driven the whole pclk-period drv_0 = 1: bit 0 is driven during the first half of the pclk-period only shift shifts the access to dxa/b and dra/b for one pclk-period (only available with double clocking mode) shift = 0: no shift takes place shift = 1: access to dxa/b and dra/b is shifted for one pclk-per. pcm-offset offset in number of data-clock periods added to time slot 0 0 0: no offset is added 0 0 1: one data clock period is added ... 1 1 1 seven data clock periods are added
peb 2466 programming the sicofi ? -4- m c semiconductor group 48 02.97 3.5.8 xr7 extended register 7 this register contains the 8-bit offset value for the level metering function bit 7 0 of7 of6 of5 of4 of3 of2 of1 of0
peb 2466 programming the sicofi ? -4- m c semiconductor group 49 02.97 3.5.9 setting of slopes in register xr6 figure 13 itd09610 0 0000000 0 1 2 3 4 5 6 7 xr6: single clock mode fsc transmit slope receive slope pclk 7 6 5 4 3 21 0 0 0 0 0 0 1 0 0 7 6 5 4 3 21 0 0 0 0 0 0 0 1 0 7 6 5 4 3 21 0 0 0 0 0 0 1 1 0 1 11 00000 0 1 2 3 4 5 6 7 1 1 000000 0 1 2 3 4 5 6 7 1 0 1 00000 0 1 2 3 4 5 6 7 double clock mode xr6: 7 6 5 4 3 21 0 0 0 0 0 0 0 0 1 pclk bit 7 time-slot 0
peb 2466 programming the sicofi ? -4- m c semiconductor group 50 02.97 3.6 the signaling interface the m c-sicofi-4 signaling interface is made up of 2 input pins (six_0, six_1), two output pins (sox_0, sox_1) and three bi-directional programmable pins (sbx_0, sbx_1, sbx_2) per channel. additional two interrupt pins (int12, int34) are provided. if one of the input pins for channel 1 or 2, or one of the bi-directional pins for channel 1 and 2 (if programmed as inputs) changes, and being stable for the debounce time specified in register xr4, int12 will go from 0 to 1. this interrupt is cleared if the appropriate registers (xr0, xr1 and xr3) are read via the serial m c-interface. pin int34 provides the same functionality for channel 3 and 4. for special purposes two additional output signals are provided by the peb 2466. chclk1 (see also register xr4) will provide a programmable time period of 2 to 28 ms. chclk2 will provide 3 different frequencies (256 khz, 512 khz or 16384 khz). both signals are only available if a valid signal is applied to the mclk-pin. 3.6.1 operating modes figure 14
peb 2466 programming the sicofi ? -4- m c semiconductor group 51 02.97 reset (basic setting mode) upon initial application of v dd or resetting pin reset to 0 during operation, or by software-reset (see xop command), the sicofi-4- m c enters a basic setting mode. basic setting means, that the sicofi-4- m c configuration registers cr0... cr6 and xr0... xr7 are initialized to 0 for all channels. all programmable filters are disabled, all programmable command/indication pins are inputs. the two tone generators as well as any testmodes are disabled. there is no persistence checking. receive signaling registers are cleared. dout-pin is in high impedance state, the analog outputs and the signaling outputs are forced to ground. if any voltage is applied to any input-pin before initial application of v dd , the sicofi-4- m c may not enter the basic setting mode. in this case it is necessary to reset the sicofi-4- m c or to initialize the sicofi-4- m c configuration registers to 0. the sicofi-4- m c leaves this mode automatically after the reset-pin is released. standby mode after releasing the reset-pin, (reset-state), the sicofi-4- m c will enter the standby mode. the sicofi-4- m c is forced to standby mode with the pu-bit set to 0 in the cr1-register (powerdown). all 4 channels must be programmed separately. during standby mode the serial sicofi-4- m c m -controller interface is ready to receive and transmit commands and data. received voice data on dra, drb-pin will be ignored. sicofi-4- m c configuration registers and coefficient-ram can be loaded and read back in this mode. data on signaling input pins can be read via the m -controller interface. cr0.. cr6 00 h xr0.. xr7 00 h coefficient-ram old value command stack cleared din-input ignored dout-output high impedance vout1,2,3,4 gnda1,2,3,4 sbx_y input sox_y gndd dxa, dxb high z vout1, 2, 3, 4 gnda1, 2, 3, 4
peb 2466 programming the sicofi ? -4- m c semiconductor group 52 02.97 operating mode the operating mode for any of the four channels is entered upon recognition of a pu-bit set to 1 in a cr1-register for the specific channel. 3.6.2 programmable filters based on an advanced digital filter concept, the peb 2466 provides excellent transmission performance and high flexibility. the new filter concept leads to a maximum independence between the different filter blocks. impedance matching filter transhybrid balancing (th) filter ? realization by 3 different loops C 4 mhz: multiplication by a constant (12 bit) C 128 khz: wave digital filter (iir) (60 bit) improves low frequency response C 64 khz: fir-filter (48 bit) for fine-tuning ? improved stability behavior of feedback loops ? real part of termination impedance positive under all conditions ? improved overflow performance for transients ? return loss better 30 db ? new concept: 2 loops at 16 khz ? flexible realization allows optimization of wide impedance range ? consists of a fixed and a programmable part C 2nd order wave digital filter (iir) (106 bit) improves low frequency response C 7-tap fir-filter (84 bit) for fine-tuning ? trans-hybrid-loss better 30 db (typically better 40 db, device only) ? adaptation to different lines by: C easy selection between four different downloaded coefficient sets
peb 2466 programming the sicofi ? -4- m c semiconductor group 53 02.97 filters for frequency response correction amplification/attenuation -filters ax1, ax2, ar1, ar2 amplification/attenuation receive (ar1, ar2)-filter amplification/attenuation transmit (ax1, ax2)-filter 3.6.3 qsicos software the qsicos-software has been developed to help to obtain an optimized set of coefficients both quickly and easily. the qsicos program runs on any pc with at least 575 kbytes of memory. this also requires ms-dos version 5.0 or higher, as well as extended memory. ? for line equalization and compensation of attenuation distortion ? improvement of group-delay-distortion by using minimum phase filters (instead of linear phase filters) ? frr filter for correction of receive path distortion C 5 tap programmable fir filter operating at 8 khz (60 bit) ? frx filter for correction of transmit path distortion C 5 tap programmable fir filter operating at 8 khz (60 bit) ? frequency response better 0.1 db ? improved level adjustment for transmit and receive ? two separate filters at each direction for C improved trans-hybrid balancing C optimal adjustment of digital dynamic range C gain adjustments independent of th-filter step size for ar-filter range 3 .. C 14 db: step size 0.02 .. 0.05 db range C 14 .. C 24 step size 0.5 db step size for ax-filter range C 3 .. 14 db: step size 0.02 .. 0.05 db range 14 .. 24 db: step size 0.5 db
peb 2466 programming the sicofi ? -4- m c semiconductor group 54 02.97 figure 15 qsicos supports: ? calculation of coefficients for the C impedance filter (im) for return loss calculation (please note that the im filter coefficients are different for the peb 2466 and for the peb 2465. qsicos calculates the programming bytes for the sicofi-4 iom version peb 2465. these bytes have to be converted with an additional tool to get the required peb 2466 programming bytes. the conversion tool qsucconv.exe is part of the qsicos software package.) C frr and frx-filters for frequency response in receive and transmit path C ar1, ar2 and ax1, ax2-filter for level adjustment in receive and transmit path C trans hybrid balancing filter (th) and C two programmable tone generators (tg 1 and tg 2) ? simulation of the peb 2466 and slic system with fixed filter coefficients allows simulations of tolerances which may be caused e.g. by discrete external components. ? graphical output of transfer functions to the screen for C return loss C frequency responses in receive and transmit path C transhybrid loss ? calculation of the peb 2466 and slic system stability . the im-filter of the peb 2466 adjust the total system impedance by making a feedback loop. because the line is also a part of the total system, a very robust method has to used to avoid oscillations and to ensure system stability. the input impedance of the peb 2466 and slic combination is calculated. if the real part of the system input impedance is positive, the total system stability can be guaranteed. itd09611 line interface interface line line interface interface line 11 k = z in g z - ()/ ) (+ z g in z g v 2 v 21 = k // k = 22 v 2 v 3 3 v 1 v 12 = k / 2 * automatic k-param extraction simulation (pspice) [hz] rd[db] country-spec k-parameter interface- file file coefficients sicofi r calculation-controlfile qsicos software for filter-coefficients-optimization ~ ~ ~ ~ f
peb 2466 transmission characteristics semiconductor group 55 02.97 4 transmission characteristics the figures in this specification are based on the subscriber-line board requirements. the proper adjustment of the programmable filters (transhybrid balancing, impedance matching, frequency-response correction) requires a complete knowledge of the m c-sicofi-4s analog environment. unless otherwise stated, the transmission characteristics are guaranteed within the test conditions. test conditions t a = 0 c to 70 c; v dd = 5 v 5%; gnda1..4 = gndd = 0 v r l 1) > 300 w ; c l < 50 pf; h(im) = h(th) = 0; h(r1) = h(frx) = h(frr) = 1; hpr and hpx enabled; ar 2) = 0 to C 9 db ax 3) = 0 to 9 db for a-law, 0 to 7 db for m -law f = 1014 hz; 0 dbm0; a-law or m -law; agx = 0 db, 6.02 db, agr = 0 db, C 6.02db; a-law a 0 dbm0 signal is equivalent to 1.095 vrms. a + 3.14 dbm0 signal is equivalent to 1.57 vrms which corresponds to the overload point of 2.223 v. when the gain in the receive path is set at 0 db, an 1014 hz pcm sinewave input with a level 0 dbm0 will correspond to a voltage of 1.095 vrms at the analog output. when the gain in the transmit path is set at 0 db, an 1014 hz sine wave signal with a voltage of 1.095vrms a-law will correspond to a level of 0 dbm0 at the pcm output. m -law in transmit direction for m -law an additional gain of 1.94 db is implemented automatically, in the companding block (cmp). this additional gain has to be considered at all gain calculations, and reduces possible ax-gain from 9 db (with a-law) to 7 db (with m -law) a 0 dbm0 4) signal is equivalent to 1.0906 vrms. a + 3.17 dbm0 signal is equivalent to 1.57 vrms which corresponds to the overload point of 2.223 v. when the gain in the receive path is set at 0 db, an 1014 hz pcm sinewave input with a level 0 dbm0 will correspond to a voltage of 1.0906 vrms at the analog output. when the gain in the transmit path is set at 0 db, an 1014 hz sine wave signal with a voltage of 1.0906 vrms will correspond to a level of 1.94 dbm0 at the pcm output. 1) r l , c l forms the load on vout 2) consider, in a complete system, ar = ar1 + ar2 + frr + r1 3) consider, in a complete system, ax = ax1 + ax2 + frx 4) the absolute power level in decibels referred to (a point of zero relative level) the pcm interface levels.
peb 2466 transmission characteristics semiconductor group 56 02.97 transmission characteristics 1) using equal-level, 4-tone method (eia) at a composite level of C 13 dbm0 with frequencies in the range between 300 hz and 3400 hz. parameter symbol limit values unit min. typ. max. gain absolute (agx = agr = 0) t a = 25 c; v dd = 5 v t a = 0 C 70 c; v dd = 5 v 5% g C 0.15 C 0.25 0.10 + 0.15 + 0.25 db db gain absolute (agx = 6.02 db, agr = C 6.02 db) t a = 25c; v dd = 5 v t a = 0-70c; v dd = 5 v 5% g C 0.15 C 0.25 0.10 + 0.15 + 0.25 db db harmonic distortion, 0 dbm0; f = 1000 hz; 2 nd , 3 rd order hd C 50 C 44 db intermodulation 1) r 2 r 3 imd imd C 46 C 56 db db crosstalk 0 dbm0; f = 200 hz to 3400 hz any combination of direction and channel ct C 85 C 80 db idle channel noise, transmit, a-law, psophometric ( v in =0v) transmit, m -law, c-message ( v in =0v) transmit, m -law, c-message ( v in = 0v) receive, a-law, psophometric (idle code + 0) receive, m -law, c-message (idle code + 0) receive, m -law, c-message (idle code + 0) n tp n tc n tc n rp n rc n rc C 85 5 5 C 67.4 17.5 17.5 C 78.0 12.0 12.0 dbm0p dbmc dbrnc0 dbm0p dbmc dbrnc0
peb 2466 transmission characteristics semiconductor group 57 02.97 4.1 frequency response figure 16 receive: reference frequency 1014 hz, input signal level 0 dbm0 figure 17 transmit: reference frequency 1014 hz, input signal level 0 dbm0
peb 2466 transmission characteristics semiconductor group 58 02.97 4.2 group delay maximum delays when the sicofi-4- m c is operating with h(th) = h(im) = 0 and h(frr) = h(frx) = 1 including delay through a/d- and d/a converters. specific filter programming may cause additional group delays. group delay deviations stay within the limits in the figures below. figure 18 group delay distortion transmit: input signal level 0 dbm0 group delay absolute values: input signal level 0 dbm0 parameter symbol limit values unit reference min. typ. max. transmit delay d xa 300. m s receive delay d ra 250 m s
peb 2466 transmission characteristics semiconductor group 59 02.97 figure 19 group delay distortion receive: input signal level 0 dbm0 1) 1) hpr is switched on: reference point is at t gmin hpr is switched off: reference is at 1.5 khz
peb 2466 transmission characteristics semiconductor group 60 02.97 4.3 out-of-band signals at analog input with an 0 dbm0 out-of-band sine wave signal with frequency f (<<100 hz or 3.4 khz to 100 khz) applied to the analog input, the level of any resulting frequency component at the digital output will stay at least x db below a 0 dbm0, 1 khz sine wave reference signal at the analog input. 1) figure 20 1) poles at 12 khz 150 hz and 16 khz 150 hz are provided 3.4 4.0 khz: x 14 C p 4000 f C 1200 -------------------- - ? ?? sin 1 C ? ?? = 4,0 4.6 khz: x18 C p 4000 f C 1200 -------------------- - ? ?? sin 7 9 -- - C ? ?? =
peb 2466 transmission characteristics semiconductor group 61 02.97 4.4 out-of-band signals at analog output with a 0 dbm0 sine wave with frequency f (300 hz to 3.99 khz) applied to the digital input, the level of any resulting out-of-band signal at the analog output will stay at least x db below a 0 dbm0, 1 khz sine wave reference signal at the analog output. figure 21 3.4 4.6 khz: x 14 C p 4000 f C 1200 -------------------- - ? ?? sin 1 C ? ?? =
peb 2466 transmission characteristics semiconductor group 62 02.97 4.5 out of band idle channel noise at analog output with an idle code applied to the digital input, the level of any resulting out-of-band power spectral density (measured with 3 khz bandwidth) at the analog output, will be not greater than the limit curve shown in the figure below. figure 22
peb 2466 transmission characteristics semiconductor group 63 02.97 4.6 overload compression figure 23 m -law, transmit: measured with sine wave f = 1014 hz.
peb 2466 transmission characteristics semiconductor group 64 02.97 4.7 gain tracking (receive or transmit) the gain deviations stay within the limits in the figures below. figure 24 gain tracking: (measured with sine wave f = 1014 hz, reference level is 0 dbm0)
peb 2466 transmission characteristics semiconductor group 65 02.97 4.8 total distortion the signal to distortion ratio exceeds the limits in the following figure. 4.8.1 total distortion measured with sine wave figure 25 receive or transmit: measured with sine wave f = 1014 hz. (c-message weighted for m -law, psophometricaly weighted for a-law)
peb 2466 transmission characteristics semiconductor group 66 02.97 4.8.2 total distortion measured with noise according to ccitt figure 26 receive figure 27 transmit
peb 2466 transmission characteristics semiconductor group 67 02.97 4.9 single frequency distortion an input signal with its frequency swept between 0.3 to 3 khz for the receive path, or 0 to 12 khz for the transmit path, any generated output signal with other frequency than the input frequency will stay 28 db below the maximum input level of 0 dbm0. 4.10 transhybrid loss the quality of transhybrid-balancing is very sensitive to deviations in gain and group delay - deviations inherent to the sicofi-4- m c a/d- and d/a-converters as well as to all external components used on a line card (slic, ops etc.) measurement of sicofi-4- m c transhybrid-loss: a 0 dbm0 sine wave signal and a frequency in the range between 300-3400 hz is applied to the digital input. the resulting analog output signal at pin v out is directly connected to v in , e.g. with the sicofi-4- m c testmode digital loop back via analog port. the programmable filters frr, ar, frx, ax and im are disabled, the balancing filter th is enabled with coefficients optimized for this configuration ( v out = v in ). the resulting echo measured at the digital output is at least x db below the level of the digital input signal as shown in the table below. (filter coefficients will be provided) the listed values for thl correspond to a typical variation of the signal amplitude and delay in the analog blocks. d amplitude = typ. 0.15 db d delay = typ 0.5 m s receive transmit frequency max input level frequency max. input level 300 hz to 3.4 khz 0 dbm0 0 to 12 khz 0 dbm0 parameter symbol limit values unit test condition min. typ. transhybrid loss at 300 hz thl 300 27 40 db t a = 25 c; v dd = 5 v; transhybrid loss at 500 hz thl 500 33 45 db t a = 25 c; v dd = 5 v; transhybrid loss at 2500 hz thl 2500 29 40 db t a = 25 c; v dd = 5v; transhybrid loss at 3000 hz thl 3000 27 35 db t a = 25 c; v dd = 5v; transhybrid loss at 3400 hz thl 3400 27 35 db t a = 25 c; v dd = 5 v
peb 2466 electrical characteristics semiconductor group 68 02.97 5 electrical characteristics note: stresses above those listed here may cause permanent damage to the device. exposure to absolute maximum rating conditions for extended periods may affect device reliability. absolute maximum ratings parameter symbol limit values unit test condition min. max. v dd referred to gndd C 0.3 7.0 v gnda to gndd C 0.6 0.6 v analog input and output voltage referred to v dd = 5 v; referred to gnda = 0 v C 5.3 C 0.3 0.3 5.3 v v all digital input voltages referred to gndd = 0 v; ( v dd =5v) referred to v dd = 5 v; (gndd = 0 v) C 0.3 C 5.3 5.3 0.3 v v dc input and output current at any input or output pin (free from latch-up) 10 ma storage temperature t stg C 60 125 c ambient temperature under bias t a C 10 80 c power dissipation (package) p d 1w
peb 2466 electrical characteristics semiconductor group 69 02.97 note: in the operating range the functions given in the circuit description are fulfilled. 1) power dissipation values are target values operating range t a = 0 to 70 c; v dd = 5 v 5%; gndd = 0 v; gnda = 0 v parameter symbol limit values unit test condition min. typ. max. v dd supply current standby operating (4 channels) i din 0.5 26 1.0 40 ma ma power supply rejection of either supply/direction receive v dd target value psrr 30 14 db db ripple: 0 to 150 khz, 70 mvrms measured: 300 hz to 3.4 khz measured: at f : = 3.4 to 150 khz power dissipation standby 1) p ds 2.5 6 mw power dissipation operating p do1 100 175 mw 1 channel power dissipation operating p do2 110 200 mw 2 channels power dissipation operating p do3 120 225 mw 3 channels power dissipation operating p do4 130 250 mw 4 channels digital interface t a = 0 to 70 c; v dd = 5 v 5%; gndd = 0 v; gnda = 0 v parameter symbol limit values unit test condition min. max. low-input voltage v il C 0.3 0.8 v high-input voltage v ih 2.0 v low-output voltage v ol 0.45 v i 0 = C 5ma high-output voltage v oh 4.4 v i 0 = 5 ma input leakage current v il 1 m a C 0.3 v in v dd
peb 2466 electrical characteristics semiconductor group 70 02.97 analog interface t a = 0 to 70 c; v dd = 5 v 5%; gndd = 0 v; gnda = 0 v parameter symbol limit values unit test condition min. typ. max. analog input resistance r i 160 270 380 k w analog output resistance r o 0.25 w analog output load r l c l 300 50 w pf input leakage current i il 0.1 1.0 m a0 v in v dd input offset voltage v io 50 mv output offset voltage v oo 50 mv input voltage range (ac) v in 2.223 v
peb 2466 electrical characteristics semiconductor group 71 02.97 5.1 coupling capacitors at the analog interface in transmit direction, a 39 nf capacitor has to be connected to v in -pins. to fulfil the frequency response requirement in receive direction, the value of the coupling capacitor ( c ext1 ) needed, depends on the input resistance of the slic-circuitry (equals the analog-output-load: r load ). figure 28 5.2 reset timing to reset the sicofi-4- m c to basic setting mode, negative pulses applied to pin reset have to be lower than 1.2 v (ttl-schmitt-trigger input) and have to be longer than 3 m s. spikes shorter than 1 m s will be ignored.
peb 2466 electrical characteristics semiconductor group 72 02.97 5.3 pcm-interface timing figure 29 single clocking mode 1) all delay times are made up by two components: an intrinsic time (min-time), caused by internal processings, and a second component caused by external circuitry (c-load) parameter symbol limit values unit min. typ. max. period of pclk t pclk 1/8192 1/128 ms pclk high time t pclkh t pclk/2 m s period fsc t fsc 125 m s fsc setup time t fsc_s 10 50 ns fsc hold time t fsc_h ( t pclk - t pclkh ) +10 ( t pclk - t pclkh ) +50 ns dra/b setup time t dr_s 10 50 ns dra/b hold time t dr_h 10 50 ns dxa/b delay time 1) t ddx 25 50 (@ 200 pf) ns dxa/b delay time to high z t ddxhz 25 50 ns tca/b delay time on t dtcon 25 50 ns tca/b delay time off t dtcoff 25 100 ns itd07276 t pclk pclk fsc dra/b dxa/b 50% fsc_s t pclkh t high imp. t dr_s dr_h t t ddx ddxhz t t fsc_h fsc t tca/b dtcon t t dtcoff
peb 2466 electrical characteristics semiconductor group 73 02.97 figure 30 double clocking mode 1) all delay times are made up by two components: an intrinsic time (min-time), caused by internal processings, and a second component caused by external circuitry (c-load) parameter symbol limit values unit min. typ. max. period of pclk t pclk 1/8192 1/256 ms pclk high time t pclkh t pclk/2 m s period fsc t fsc 125 m s fsc setup time t fsc_s 10 50 ns fsc hold time t fsc_h 2x( t pclk C t pclkh ) +10 2x( t pclk C t pclkh ) +50 ns dra/b setup time t dr_s 10 50 ns dra/b hold time t dr_h 10 50 ns dxa/b delay time 1) t ddx 25 50 (@200 pf) ns dxa/b delay time to high z t ddxhz 25 50 ns tca/b delay time on t dtcon 25 50 ns tca/b delay time off t dtcoff 25 100 ns itd07277 t pclk pclk fsc dra/b dxa/b 50% fsc_s t pclkh t high imp. t dr_s dr_h t t ddx ddxhz t t fsc_h fsc t tca/b dtcon t t ddtcoff
peb 2466 electrical characteristics semiconductor group 74 02.97 5.4 m -controller interface timing figure 31 1) all delay times are made up by two components: an intrinsic time (min-time), caused by internal processings, and a second component caused by external circuitry (c-load) parameter symbol limit values unit min. typ. max. period of dclk t dclk 1/8192 ms dclk high time t dclkh t dclk/2 m s cs setup time t cs_s 10 50 ns cs hold time t cs_h 30 50 ns din setup time t din_s 10 50 ns din hold time t din_h 10 50 ns dout delay time 1) t ddout 30 100 ns dout delay time to high z t ddouthz 30 100 ns itd07278 dclk cs din dout cs_s t high imp. t din_s din_h t t ddout ddouthz t t dclkh 50% dclk t t cs_h
peb 2466 electrical characteristics semiconductor group 75 02.97 5.5 signaling interface 5.6 from the m c-interface to the so/sb-pins (data downstream) 5.7 from the si/sb-pins to the m c-interface (data upstream) there is no way specifying the time when data applied to si-pins (and sb-pins if programmed as signaling input pins) is sampled by the peb 2466. the time only depends on internal signals (16 mhz masterclock, and status of various counters), and there is no link to a low frequency external signal. 1) all delay times are made up by two components: an intrinsic time (min-time), caused by internal processings, and a second component caused by external circuitry (c-load) parameter symbol limit values unit min. typ. max. so/sb delay time 1) t dsout 30 100 ns sb to z - time t dsbz 40 100 ns sb to drive-time t dsbd 40 100 ns
peb 2466 package outlines semiconductor group 76 02.97 6 package outlines p-mqfp-64 (plastic metric quad flat package) gpm05250 sorts of packing package outlines for tubes, trays etc. are contained in our data book package information. dimensions in mm smd = surface mounted device
peb 2466 appendix semiconductor group 77 02.97 7 appendix 7.1 level metering function this function allows a selftest of the sicofi-4 and also of the slic circuitry connected to the analog interface. the receive path has to be stimulated with a sine wave applied to the digital input, or generated by one of the internal tone generators. by closing an internal or external (via the slic) loop to the transmit path, the outgoing signal is compared with a programmable offset. (for further information, an application-note describing the calculation of the offset value and the sensitivity, is available)
peb 2466 appendix semiconductor group 78 02.97 figure 32
peb 2466 appendix semiconductor group 79 02.97 7.2 programming the sicofi ? -4- m c tone generators two independent tone generators are available per channel. switching on/off the tone generators is done by a sop-command for cr1-register. the frequencies are programmed via a cop-command, followed by the appropriate byte-sequence. when one or both tone-generators are switched on, the voice signal is switched off, if v+t=0 (cr2) for the selected voice channel. to make the generated signal sufficient for dtmf, a programmable bandpass-filter is included. the default frequency for both tone generators is 1000 hz. the qsicos-program contains a program for generating coefficients for variable frequencies. byte sequences for programming both the tone generators and the bandpass-filters: the resulting signal amplitude can be set by transmitting the ar1 and ar2 filters. by switching a digital loop the generated sine-wave signal can be fed to the transmit path. 1) 0c is used for programming tone generator 1, in channel 1 0d is used for programming tone generator 2, in channel 1 table 2 frequency command byte 1 byte 2 byte 3 byte 4 697 hz 0c/0d 1) 0a 33 5a 2c 800 hz 0c/0d 1) 12 d6 5a c0 950 hz 0c/0d 1) 1c f0 5c c0 1008 hz 0c/0d 1) 1a ae 57 70 2000 hz 0c/0d 1) 00 80 50 09
peb 2466 proposed test circuit semiconductor group 80 02.97 8 proposed test circuit figure 33 its09614 64 63 62 61 1f 10 f 10 f 1f 220 nf f 1 10 f 10 52 53 54 55 1 60 59 58 57 56 dda34 v dda12 v in4 v gnda4 gnda3 v out4 v dda34 v out3 in3 v ddref v ref v in2 v gnda2 gnda1 out2 v dda12 v out1 v in1 v gnda3 gnda4 gnda2 gnda1 ddref v 12 3 4 5 6 11 12 13 14 15 7 8 9 10 16 41 42 43 44 45 46 47 48 40 39 38 37 36 35 34 33 sb3_0 sb3_1 sb3_2 so3_1 so3_0 so4_0 so4_1 sb4_0 sb4_1 sb4_2 si4_0 si4_1 int34 sb2_2 sb2_1 sb2_0 so2_1 so2_0 so1_0 so1_1 sb1_0 sb1_1 sb1_2 si1_0 si1_1 int12 1-10 f + 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 cs dclk din dout gndd mclk reset tca dxa dra tcb dxb drb fsc pclk ddd v 1 = si3_1 2 = si3_0 47 = si2_0 48 = si2_1 33 = chclk1 16 = chclk2 m0381 sicofi 4 r c - gnda2 gnda1 dda12 v v ddref gnda3 gnda4 dda34 v gnda4 gnda3 v dda34 mclk v ddd gndd gnda2 v ddref v dda12 gnda1 out4 v in4 v v out3 in3 v v in2 out2 v out1 v v in1 * * * * * * pclk fsc dr dx 9 8, 7, 6, 2 3 4 5 gnd cs dclk din dout pc printer-port (25 pin sub-d plug) (9-pol. sub-d plug) 22 61 21 20 pcm4 as near as possible to the pin 220 nf an v ref = banana-bush bnc-bush = filter-cs: * + 100 nf smd as near as possible to the pin 2.2 f ta-cap. all resistors: app. 680 k w 51 50 49 = test-point m m m m m m m m m f m f m
peb 2466 guidelines for board-design semiconductor group 81 02.97 9 guidelines for board-design 9.1 board layout recommendation keep in mind that inside the sicofi-4- m c all the different v dd -supplies are connected via the substrate of the chip, and the areas connected to different grounds are separated on chip. a) separate all digital supply lines from analog supply lines as much as possible. b) use a separate gnd-connection for the capacitor which is filtering the reference voltage (220 nf ceramic-capacitor at v ref ). c) dont use a common ground-plane under the sicofi-4- m c. d) use a large ground-plane (distant from the sicofi-4- m c) and use three single ground lines for connecting the sicofi-4- m c: one common analog ground, one digital ground, and a third for the 220 nf capacitor connected to v ref . 9.2 filter capacitors a) to achieve a good filtering for the high frequency band, place smd ceramic-capacitors with 100 nf from v dda12 , v dda32 and v ddref to gnda. b) one 100 nf smd ceramic-capacitor is needed to filter the digital supply ( v ddd to gndd). c) place all filter capacitors as close as possible to the sicofi-4- m c (most important!!!). d) use one central tantalum-capacitor with about 1 m f to 10 m f to block v dd to gnd.
peb 2466 guidelines for board-design semiconductor group 82 02.97 9.3 example of a peb 2466-board figure 34 its09615 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 53 54 55 56 58 59 60 62 63 64 17 18 19 20 21 22 23 25 26 27 28 29 30 31 32 16 100 nf ceramic ddd v gndd 100 nf ceramic ceramic nf 100 ceramic nf 100 gnda1 gnda2 gnda3 gnda4 gnd 1-10 f tantal dd v 220 nf dda12 v v ref v ddref v dda34 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 m dd v dd v dd v peb 2466 h dd v

▲Up To Search▲

Price & Availability of PEB2466-HV12

	To Download PEB2466-HV12 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .